2 Synergy SYN 12 d4 and Synergy WFO3.1 package

Synergy Audio is proud to bring you our new Synester Series 1250 rms subwoofer. Starting with a triple 190mm diameter Y35 strontium ferrite magnet slugs, bolted between a 20mm thick low carbon steel top plate washer and a one piece bumped bottom plate T-Yoke with an extended pole. A pole chamfer at the top and a flared vent along with 12 magnetic gap vents on the bottom plate create maximum cooling. We utilized a high temperature 4 layer 3″ voice coil, black aluminum former wound with high temp aluminum wire for high power handling. We utilized a non pressed pulp paper cone with red double stitching, a high roll foam surround and dual red 10″ nomex spiders with stitched tinsel leads to assure a strong, accurate loud daily subwoofer. We tooled a 6 spoke heavy duty cast aluminum frame finished in gloss black finish to assure an accurate, reliable and mechanically stable musical platform all the while looking great and sounding SYNESTER.

Specifications: 12D2

• Re = 4.00 ohm
• Fs = 38.571Hz
• Sd = 530.930 cm
• Bl = 24.337Tm
• Qms = 6.645
• Qes = 0.605
• Qts = 0.554
• SPL = 88.3dB
• Vas = 29.224L
• Cms = 73.010m mm/N
• Mms = 268.430g
• Voice Coil = 3.00″
• RMS Power = 1250 watts
• Suggested Ported = 2.0 – 3.0ft^3
• Cutout Diameter: 11.5625"
• Mounting Diameter: 12.875"

Specifications: 12D4:

• Re = 6.40 ohm
• Fs = 39.571Hz
• Sd = 530.930 cm
• Bl = 24.496Tm
• Qms = 7.805
• Qes = 0.756
• Qts = 0.689
• SPL = 88.3dB
• Vas = 22.714L
• Cms = 56.744m mm/N
• Mms = 285.119g
• Voice Coil = 3.00″
• RMS Power = 1250 watts
• Suggested Ported = 2.0 – 3.0ft^3
• Cutout Diameter: 11.5625"
• Mounting Diameter: 12.875"

WFO 3.1D Specs:

• Power @ 1 Ohm: 3500w @ 12.6v
• Power @ 2 Ohm: 2350w @ 12.6v
• Power @ 4 Ohm: 1200w @ 12.6v
• Power @ 1 Ohm: 4700 @ 16v
• Frequency Response: 12hz – 250hz
• Signal to Noise Ratio: >100db
• Damping Factor: 300 >
• Input Sensitivity: 8V - 0.2V
• Variable Subsonic Filter: 10Hz - 50Hz
• Variable Low Pass Filter: 35Hz – 250Hz
• THD @ 4ohm: < 0.1%
• Fuse Rating: 300A
• Strapped Fuse Rating: 600A
• Dimensions: 480mm L x 239mm W x 68.5mm H
• (2) 0 GA Power & Ground Terminals
• (4) 8 gauge speaker inputs
• Panel locking Tiffany RCA inputs/outputs
• 16v Working Voltage
• 4 Power Transformers
• Heavy Duty 3oz printed circuit board

All WFO series amplifier feature:

• Custom high mass, thermally optimized aluminum heat sink casing with removable center insert for installation integration.
• Overbuilt power supplies and output sections utilizing high grade components
• Heavy duty double sided through hole PCB’s with thick solid copper heavy duty traces
• Panel locking Tiffany RCA inputs/outputs
• Single, Double and Triple 1/0 gauge nickel plated power and ground inputs
• Nickel plated 8 gauge speaker outputs
• Fully linkable/strappable (Mono-block)
• Input sensitivity 8V – 0.2V
• +18db Remote Gain control
• Multi-way fully intelligent circuitry for maximum protection